Dongguan Chenglue Electronic co.,Ltd
Dongguan Chenglue Electronic co.,Ltd
Add to Cart
Small Size 220K 400VAC Y1 Safety Capacitor Flame-Retardant Epoxy Resin Package
Y1 Safety Capacitor .pdf
Y1 capacitors are specially designed for AC appliances, comply with a number of safety certification standards, and are suitable for cross-line and bypass circuits. And it is suitable for AC circuits, compact in size, high in cost performance, and meets the safety standards of AC circuits. The X and Y capacitors are safety capacitors, the X capacitor is between the live wire and the neutral wire, and the Y capacitor is between the live wire and the ground. They are used in the power supply filter to play the role of power supply filtering, and filter the common mode (Y capacitor) and differential mode (X capacitor) interference respectively.
Feature
1. Small size.
2. AC capacitors that have passed and complied with safety certification.
3. The high-frequency loss is small, and it can withstand the impact of AC peak surges.
4. Strong over-current capability, small capacity and loss attenuation.
5. Long service life.
6. The rated voltage of Y1 is 400-500VAC, and the experimental voltage is 4000VAC.
7. Y capacitors often use high-voltage ceramics.
8. Y1 is a double-insulated Y capacitor, which is used to bridge the primary and secondary sides.
9. Flame-retardant epoxy resin package.
10. X capacitors and Y capacitors are collectively referred to as safety capacitors. Safety capacitors are used in such occasions, that is, after the capacitor fails, it will not cause electric shock and will not endanger personal safety.
|
ITEM |
SPECIFICATION |
TEST METHOD AND CONDITION | ||||||||||||||||
| Temp Cycling
|
Appearance |
No marked defect |
The capacitor shall be introduced into the test chamber, and shall be exposed to the temperature conditions as shown in table at 5 cycles. pretreatment: The capacitor shall be placed at 125±2℃ for 1 hour, then placed at room condition for 24±2hours before initial measurement. Post-treatment: Capacitor shall be stored for 24±2 hours at room conditions.
| |||||||||||||||
|
Capacitance Change | B:±10% max E:±20% max F:±30% max | |||||||||||||||||
|
D.F. | B,E:5.0% max F:7.0% max | |||||||||||||||||
|
I.R. | 1000MΩ min | |||||||||||||||||
|
Humidity (Under Steady State) |
Appearance |
No marked defect |
Set the capacitor for 500±12 hours at 40±2℃ in 95±3% RH. pre-treatment: The capacitor shall be placed at 125±2℃ for 1 hour, then placed at room condition for 24±2 hours before initial measurement. Post-treatment: The capacitor shall be stored for 24±2 hours at room condition. | |||||||||||||||
|
Capacitance Change | B:±10% max E:±20% max F:±30% max | |||||||||||||||||
|
D.F. | B,E:5.0% max F:7.0% max | |||||||||||||||||
|
I.R. | 1500MΩ min | |||||||||||||||||
|
Dielectric Strength |
Per Item 8 | |||||||||||||||||
|
Life Test |
Appearance |
No marked defect | Apply a voltage of 500V.AC,except that once each hour the voltage is increased to 1000V.AC for 0.1sec.that shall be maintained for 1000±48 hours at 125±2℃. Pre-treatment: Capacitor shall be stored at 125±2℃ for 1 hour, then placed at room condition for 24±2H before initial measurements. Post-treatment: Capacitor shall be stored for 24±2 hours at room condition. | |||||||||||||||
|
Capacitance Change | B:±10% max E:±20% max F:±30% max | |||||||||||||||||
|
D.F. | B,E:5.0% max F:7.0% max | |||||||||||||||||
|
I.R. | 1500MΩ min | |||||||||||||||||
Product Voltage, Material, Size reference Table
| Product and size code | Rated AC Voltage | Temperature Characteristic | Rated Capacitance | Tolerance of Capacitance | Size (mm) | |||
| D.max | T.max | P±0.8 | d±0.05 | |||||
| Q065B□□100K□ | 400Vac | (B) | 10pF | K | 6.5 | 4.5 | 10 | 0.55 |
| Q065B□□150K□ | 15pF | 6.5 | 4.5 | 10 | 0.55 | |||
| Q070B□□220K□ | 22pF | 7.0 | 4.5 | 10 | 0.55 | |||
| Q070B□□330K□ | 33pF | 7.0 | 4.5 | 10 | 0.55 | |||
| Q070B□□470K□ | 47pF | 7.0 | 4.5 | 10 | 0.55 | |||
| Q070B□□560K□ | 56pF | 7.0 | 4.5 | 10 | 0.55 | |||
| Q070B□□620K□ | 62pF | 7.0 | 4.5 | 10 | 0.55 | |||
| Q070B□□820K□ | 82pF | 7.0 | 4.5 | 10 | 0.55 | |||
| Q065B□□101K□ | 100pF | 6.5 | 4.5 | 10 | 0.55 | |||
| Q065B□□221K□ | 220pF | 6.5 | 4.5 | 10 | 0.55 | |||
| Q075B□□331K□ | 330pF | 7.5 | 4.5 | 10 | 0.6 | |||
| Q085B□□471K□ | 470pF | 8.5 | 4.5 | 10 | 0.6 | |||
| Q085B□□561K□ | 560pF | 8.5 | 4.5 | 10 | 0.6 | |||
| Q095B□□681K□ | 680pF | 9.5 | 4.5 | 10 | 0.6 | |||
| Q110B□□821K□ | 820pF | 11.0 | 4.5 | 10 | 0.6 | |||
| Q115B□□102K□ | 1000pF | 11.5 | 4.5 | 10 | 0.6 | |||
| Q065E□□471K□ | (E) | 470pF | 6.5 | 4.5 | 10 | 0.55 | ||
| Q075E□□561K□ | 560pF | 7.5 | 4.5 | 10 | 0.6 | |||
| Q075E□□681K□ | 680pF | 7.5 | 4.5 | 10 | 0.6 | |||
| Q075E□□821K□ | 820pF | 7.5 | 4.5 | 10 | 0.6 | |||
| Q085E□□102K□ | 1000pF | 8.5 | 4.5 | 10 | 0.65 | |||
| Q095E□□152M□ | 1500pF | M | 9.5 | 4.5 | 10 | 0.65 | ||
| Q105E□□222M□ | 2200pF | 10.5 | 4.5 | 10 | 0.65 | |||
| Q115E□□332M□ | 3300pF | 11.5 | 4.5 | 10 | 0.65 | |||
| Q065F□□102M□ | (F) | 1000pF | 6.5 | 4.5 | 10 | 0.55 | ||
| Q075F□□152M□ | 1500pF | 7.5 | 4.5 | 10 | 0.6 | |||
| Q085F□□222M□ | 2200pF | 8.5 | 4.5 | 10 | 0.6 | |||
| Q100F□□332M□ | 3300pF | 10.0 | 4.5 | 10 | 0.65 | |||
| 4700pF | 11.5 | 4.5 | 10 | 0.65 | ||||
Specification and Test Method
| ITEM | SPECIFICATION | TEST METHOD AND CONDITION | |||||||||||||
| Storage Temp. Range | -40℃~+125℃ | ||||||||||||||
| Operating Temp. Range | -25℃~+125℃ | ||||||||||||||
| | Appearance has | | |||||||||||||
| | | | |||||||||||||
| | | Temp. 20±2℃ | |||||||||||||
| Dissipation Factor | B,E:2.5% max | | |||||||||||||
| | 10,000MΩ | | |||||||||||||
| | | | | ||||||||||||
| | | | |||||||||||||
| | B:-10~+10% |
| |||||||||||||
Production Process
